A built in shower bench earns its place when somebody will sit in the shower. Settle its height and the floor it takes on the plan. Settle what’s behind it there, too. The bench is framed, waterproofed and tiled along with the shower, so it can’t be adjusted afterward.
That’s why timing matters. A seat at the wrong height, a shower with too little standing room, or a wall that can’t carry the bench can each mean opening finished walls to change it. All of that is easier to settle on paper.
Does Your Shower Need a Built In Shower Bench?
It does if somebody will sit in it. People sit to rest, to shave, to wash a child or to get help from someone else. In a small shower, where you need the floor to turn around in, the answer can be no. A bench there takes floor you’d rather keep for moving.
So the planning question is who sits, and how often. Picture the people who’ll use this shower over the years you plan to stay. Someone who shaves seated. A parent washing a toddler. Someone who’d like a place to rest. If nobody comes to mind, the floor may serve you better than a seat.
The same goes for a tub-to-shower conversion. The space the tub held sets the floor you have, and a bench takes part of it.
A larger shower has room for built-in benches, curbless entry, handheld showerheads and grab bars, one of the reasons to prioritize a large shower.
How High and How Deep Should a Shower Bench Be?
For height, the federal Access Board’s guide gives 17 to 19 inches for a shower seat, measured to the finish floor. It says that height “approximates wheelchair seat heights.” That’s a published benchmark for buildings the ADA covers, not a rule for a private home. Depth is a separate planning call.
The federal Access Board’s guide to bathing rooms also says a transfer-shower seat has to reach to within 3 inches of the compartment entry. A transfer shower is the compact kind with a seat that a person moves onto. Keeping that gap small makes the move easier.
Depth is the part a height figure doesn’t answer. A deeper seat can hold a person better, but it takes more of the floor. A shallow one takes less. It may only hold a foot or a bottle. Decide depth from who sits. Then look at what’s left for standing, turning and the door swing.
In one McDaniels bathroom, a frameless glass hinged door opens onto a large alcove shower with a built-in bench.
What Does the Wall Behind a Shower Bench Need?
It needs backing planned before the walls close. That’s solid reinforcement in the wall that a seat or bar anchors to. The Access Board’s guide says seats in accessible showers must withstand 250 pounds “at any point on the seat, fastener, mounting device, or supporting structure.” It also says a seat isn’t required in dwelling units if walls are properly reinforced for one later.
In the Access Board’s transfer-shower layout, the grab bars run along the back wall and the wall across from the seat, so the seat helps decide where the bars go. Plan grab bar placement on the same drawing, because each bar needs support behind it, too.
Settle these on the plan before the walls close:
- Where the bench goes, or where a later seat could go.
- What framing and backing sit under and behind it.
- Where the grab bars go beside it.
- Who marks the support on the drawing.
Reinforcing the walls for a seat is one way to keep the option open in a small shower. You keep the floor clear. And the wall is ready if a seat is wanted later.
How Does Water Leave the Seat?
A bench sits inside the wet area, so it needs the same thinking as the floor. Water on the seat needs a way to reach the drain. And the waterproofing has to cover the bench along with the walls and floor. Both belong on the plan.
One shower-system maker’s guide makes this point about floors. With a linear drain, a single pitch toward the drain gives water “one uniform path to the drain,” the maker says. It also helps avoid “standing-water” dead spots.
That maker is talking about a shower floor. The same principle gives you the question to ask about a seat. How will it shed water? What waterproofing covers it? Ask your designer to show both answers on the plan.
What Should You Ask Before the Walls Close?
Bring the people and the room into the conversation. Tell the designer who’ll use the shower, and share the space you have to work with. Then ask the designer to draw the bench into the plan, so its height, depth and backing are on paper before anything is ordered. These questions can help.
- Who will sit on the bench, and how often?
- How high should the seat be for them?
- How much standing and turning room is left with the bench drawn in?
- What backing sits behind it, and where could later bars go?
- How will the seat shed water, and what waterproofing covers it?
For bathroom remodeling, McDaniels designs everything from compact hall baths to primary suites. Your designer settles where the shower goes. Installation is done by McDaniels’ installation partner or your own contractor. So the bench belongs on the plan before products are ordered.
Frequently Asked Questions About Built In Shower Benches
Can a shower bench be added after the shower is built?
A built-in bench is part of the shower’s framing and waterproofing, so it belongs on the plan. Adding one after the tile can mean opening finished walls. If you’re not sure you want a seat yet, there’s another path. For dwelling units, the Access Board’s guide doesn’t require a seat when the walls are properly reinforced to take one later. That keeps the choice open.
Does a bench change where the grab bars go?
Yes. The Access Board’s guide lays out the bars differently when a seat is in the plan. A transfer shower puts them on the back wall and the wall across from the seat. A roll-in shower with no seat gets bars on three walls. Walls can be reinforced for bars added later, too. So mark the bench and the bars on the same drawing.
Is a bench a good idea in a small shower?
It can be, but a bench can crowd the room you need to stand and turn. If the floor is tight, ask your designer to draw the shower both ways: once with the bench and once without. Seeing them side by side makes the trade clear. If you leave the seat out, reinforced walls keep one possible later.
Does a built-in bench need to be waterproofed?
Yes. It sits inside the wet area, so ask how the waterproofing covers the bench along with the walls and floor. Ask how the seat will shed water, too. One shower-system maker’s point about a single pitch toward the drain is about floors. But the same question applies to a seat: where does the water go?
What should I bring to a bathroom design consultation?
Bring photos and measurements of the shower you have. Add a note on who will sit in the shower after the remodel, and how often. Then bring your questions about height, standing room, backing and drainage. McDaniels’ experienced designers offer complimentary consultations, so the bench can be part of the plan early.
Settle the Bench Before the Walls Close
We designed a bathroom with a recessed, tiled storage niche, a built-in shower bench and a grab bar.
A built in shower bench is easy to say yes to on a plan and hard to change after the tile. So size it and back it while the walls are open, and ask how it drains.
When you’re ready, book a complimentary design consultation and bring the people who’ll use the shower into the plan.